fixing the bow of a mirror dinghy

inside bow locker finished

As promised some more pictures of the bow locker repairs. please note that the runs in this picture are from the origonal work not mine!! You can see the stringer that will support the fore deck and into which I will screw fix the deck. I gave the stringer a liberal coat of west system resin before fitting the deck to act as a glue.

underside of bow deck

the supports under the fore decks  were the originals re used

fore deck fitted prior to fixing

I fixed the deck with stainless steel screws aw 150mm centres to the stringer . These screws will be hidden with the fibreglass tape.

 

fixing a mirror dinghy

I used some oak that I had in the shed to make a new section of gunwhale for the bow. This is now glued into place with West system resin.

New gunwale detail

When the resin went off I drilled and screw fixed the gunwales for additional strength

screwing the gunwales

Be careful when buying brass screws, these are scarce now and most of the screws that you see in the hardware stores are yellow metal and will corrode in salt water. I went to a chandler to get proper brass screws, and I never throw out brass fittings or screws!.

 

fixing the bow of a mirror dinghy

I have replaced the backing for the bow which holds the forward chain plate. I glued this into place with waterproof glue and screwed it with brass screws through the bow plate.  The next step is painting

I re used all of the forward deck support timbers , simply to save on the effort of copying them. These were screwed and glued into place prior to painting the inner lockers.

the bow lockers. I am using International paints starting with precoat (3 coats) and then finishing with International gloss

Always use the best paint available.

I find that the International range of paints are very good, they give good coverage and a high level of opacity per coat. Don’t try to save money on cheap non marine paints it really is not worth it. This is particularly true when painting inside lockers where future maintenance will be troublesome.

 

Rot in bow lockers

Find the edge of the rot and cut to square

back plate inserted and stitched with copper wire

inserted repair panel wire stitched to back panel and glued with resin

 

mirror dinghy restoration

rotten bow about to be removed

After searching around for good quality marine ply I have finally removed the bow  and used the existing bow plate as a template to cut the new one.

use only the best quality plywood

I was surprised at the amount of plywood that is sold as marine ply. If you are replacing any panels in your mirror you would be well advised to search around to find true marine ply. A word of warning a sheet of lloyds registered 4mm marine ply cost € 75 + vat. It ain’t  cheap but it is far better quality than other plywoods that I have found on the market.

bow panel used as template

 

mirror dinghy restoration

I decided to to a bare wood restoration so I have stripped all of the varnish and paint off with a view to finding any rot. Generally when there are areas of blackened ply it will be rotten or weakened so  the first things to be replaced are the foredeck panels which I have carefully removed so that I can use them as templates. this has also allowed access to the forward  tanks. I have found rot here so I need to make some decisions as to how I will deal with it. I used broken picture glass as a scraper to remove varnish and paint stripper on the hull.

It is also clear that much of the fibreglass tape will have to be removed and replaced, as well as the bow panel. there is also some rot in the bulkheads where the fibreglass tape had failed.  The most difficult part of this stage is successfully removing the fibreglass without further damaging the woodwork.

looking at the overall condition of the boat and weighing this up against what the boat will be used for ( this is a boat for the kids to learn to sail in and have  fun rather than a show piece) I think that I will line the bow lockers with a layer of chopped strand mat and resin rather than replacing these sections of the plywood.  I will have to be careful not to use too much resin as I don’t want too much weight up there.

rotten bow section missing knees

all paint and varnish removed for bare wood restoration

rot in bow lockers, the hole formed with hand pressure! The question is how far to go.

 

Mirror dinghy restoration

After getting the dinghy home and rigging it I made some good and bad discoveries. My first mishap was when I put my hand through the bow panel which was very rotten- not a good start.  however when I unloaded the trailer I found two complete sets of rigging both standing and running and three suits of sails – one a racing suit and one a standard suit. there was also a spinaker abd chute but no chute bag or spinaker pole. there was also a large amount of bits and pieces such as blocks, cleats  pintles gudgeons etc. there was also a fair amount of rope but as I would dsicover not enough. later I will prepare an inventory of what rope a completed mirror should have.

The boat had no oars or rowlocks, and I would advise anybody buying a mirror to insist on these as they are hard to find. – if anybody out there has mirror oars and they would like to part with them I would be happy.

By the serial number I reckon that the boat is early 70’s but I will check up on this later.

 

Mirror dinghy restoration

the trailer seemed to be in good condition but there were some issues!

a bit of work to be done here

After much browsing I have discovered a Mirror dinghy for sale on a good quality trailer. The trailer is a Brownlowe trailer (an Irish manufacturer who makes excellent trailers using indespention parts. I put a bid on the lot and agreed a sale. As you can see from the photographs the boat requires restoration, in fact the boat was even worse than the photographs would indicate. any comments from others with similar projects are welcome